螺母知识之扣压尺寸表
来源：网络 作者：网络转载 2019-10-09 阅读：657
| 代号(M) | 螺纹(M) | 扣压前直径 | 扣压后直径±0.1 | 扣压高度±0.2 |
| M10 | M10 | 13.8 | 11.5 | 3 |
| M12 | M12 | 16.7 | 14.6 | 3 |
| M14 | M14 | 18.7 | 16.7 | 3 |
| M16 | M16 | 21.7 | 19.6 | 3.5 |
| M18 | M18 | 23.7 | 21.2 | 4 |
| M20 | M20 | 26.7 | 24.3 | 4.5 |
| M22 | M22 | 26.7 | 24.1 | 4.5 |
| M24 | M24 | 29.7 | 27.1 | 5 |
| M24(286) | M24(286) | 31.5 | 29.1 | 5 |
| M26 | M26 | 31.7 | 29.1 | 5 |
| M27 | M27 | 31.7 | 29.1 | 5 |
| M30 | M30 | 35.7 | 32.6 | 5 |
| M33 | M33 | 40.5 | 37.5 | 5 |
| M36 | M36 | 40.5 | 37.5 | 5 |
| M39(207) | M39×32 | 45.5 | 42.7 | 5 |
| M42 | M42 | 49.5 | 46.5 | 5.5 |
| M45 | M45 | 54.5 | 51.6 | 6 |
| N04SW/S | Z1/4×18 | 18.7 | 16.2 | 3 |
| N06SW/S | Z3/8×18 | 21.8 | 19.1 | 3 |
| N08SW/S | Z1/2×14 | 26.7 | 24 | 4.5 |
| N12SW/S | Z3/4×14 | 31.8 | 28.9 | 5 |
| N16SW/S | Z1×11 | 40.8 | 37.5 | 6 |
| G06SW/S | G3/8×19 | 21.8 | 19.1 | 3 |
| G12SW/S | G3/4×14 | 31.8 | 28.9 | 5 |
| Y04 | | 24 | 21.5 | 4 |
| Y06 | | 30 | 27.5 | 4.5 |
| Y08 | | 32.6 | 30.1 | 4.5 |
| Y12 | | 43 | 40.2 | 5.5 |
| Y16 | | 54 | 50.7 | 5.5 |
| B02 | G1/8 | 13.7 | 11.8 | 3 |
| B04 | G1/4 | 18.7 | 16.6 | 3 |
| B04FS09 | G1/4×19 | 17.5 | 16.2 | 3 |
| B06 | G3/8 | 21.7 | 19.6 | 3.5 |
| B08 | G1/2 | 26.7 | 24.2 | 4.5 |
| B10 | G5/8 | 29.7 | 27.2 | 5 |
| B12 | G3/4 | 31.7 | 29.1 | 5 |
| B16 | G1 | 40.5 | 37.7 | 5 |
| B20 | G1.1/4×11 | 49.5 | 46.9 | 5.5 |
| J04 | 7/16 | 14.9 | 12.6 | 3 |
| J04NJ12 | 7/16 | 14.3 | 12.6 | 3 |
| J05 | 1/2 | 16.7 | 14.5 | 3 |
| J06 | 9/16 | 18.7 | 116.5 | 3 |
| J06NJ12 | 9/16 | 17.7 | 15.7 | 3 |
| J08 | 3/4 | 23.7 | 21.2 | 4 |
| J08NJ12 | 3/4 | 23.7 | 21.9 | 4 |
| J10 | 7/8 | 26.7 | 24.1 | 4.5 |
| J10NJ12 | 7/8 | 26.7 | 24.8 | 4.5 |
| J12 | 1.1/16 | 31.7 | 29.1 | 5 |
| J12NJ12 | 1.1/16 | 31.7 | 29.1 | 5 |
| J14 | 1.3/16 | 35.7 | 32.6 | 5 |
| J16 | 1.5/16 | 40.5 | 37.7 | 5 |
| J20 | 1.5/8 | 49.5 | 46.6 | 5.5 |
| F04 | 9/16 | 18.7 | 16.5 | 3 |
| F06 | 11/16 | 21.7 | 19.6 | 3.5 |
| F08 | 13/16 | 26.7 | 24.1 | 4.5 |
| F10 | 1 | 29.7 | 27.1 | 5 |
| F12 | 1.3/16 | 35.7 | 32.6 | 5 |
| F16 | 1.7/16 | 40.7 | 37.2 | 5 |
| F20 | 1.11/16 | 49.7 | 47 | 5.5 |
| O06SW/S | 9/16×18 | 21.8 | 19.1 | 3.5 |
| O10SWSAU | | 26.6 | 23.8 | 4.5 |
| P06 | 5/8 | 21.7 | 19.2 | 3.5 |
| P12 | 1.1/16 | 31.7 | 29.1 | 5 |
| U02 | 1/8×27NPSM | 14.7 | 13 | 3 |
| U04 | 1/4NPSM | 18.7 | 16.6 | 3 |
| U06 | 3/8NPSM | 21.7 | 19.5 | 3.5 |
| U08 | 1/2NPSM | 26.7 | 24.2 | 4.5 |
| U12 | 3/4NPSM | 31.7 | 29.1 | 5 |
| U16 | 1NPSM | 40.5 | 37.7 | 5 |
| 模具型号 | 9 | 12 | 16 | 22 |
| 对边S | S﹤17 | 17≤S≤19 | 22≤S≤24 | 27≤S≤30 |
| 模具型号 | 26 | 27 | 30 | 34 |
| 对边S | S=32 | 32≤S≤36 | S=36 | 41≤S≤46 |
| 模具型号 | 41 | 45 | 63 | |
| 对边S | 50≤S≤55 | 55≤S≤65 | 70≤S≤75 | |
QQ交流群
